Requirements for manufacturers and suppliers of e-micromobility products

The products must comply with any one of the Standards listed for the product category below.

e-bikes

For e-bikes with a maximum continuous rated output not exceeding 500 watts

• AS 15194:2016 - Cycles - Electrically power assisted cycles - EPAC Bicycles (also known as pedelecs): Limited to Clauses 4.2 (all - except requirements of Electro Magnetic Compatibility), Clause 5 (all - except requirements of AS/NZS 1927) and Clause 6 (all - except requirements of AS/NZS 1927), or
• EN 15194:2017+A1:2023 - Cycles - Electrically power assisted cycles - EPAC Bicycles: Limited to Clauses 4.2 (all - except requirements of Electro Magnetic Compatibility), Clause 5 and Clause 6. References to EN 60335-2-29 (battery chargers) have been replaced by AS/NZS 60335.2.29, or
• UL 2849:2022 - Electrical systems for eBikes

For e-bikes with a maximum continuous rated output exceeding 500 watts

• UL 2849:2022 - Electrical systems for eBikes

e-bike batteries 

• EN 50604-1:2016+A1:2021 - Secondary lithium batteries for light EV (electric vehicle) applications, or
• IEC 62133-2:2017 - Secondary cells and batteries containing alkaline or other non-acid electrolytes- Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications- Part 2: Lithium systems, or
• UL 2271:2018 - Batteries for use in light electric vehicle (LEV) applications (until 1 February 2027) or UL 2271:2023

Note: References to “EN 50604-1” in clause 4.2 of EN 15194:2017 + A1:2023 or AS 15194:2016 are replaced by “EN 50604-1:2016 +A1:2021 or IEC 62133-2:2017 or UL 2271”.

The specifications for AS 15194:2016 and EN 15194:2017 +A1:2023, compliance to the relevant clauses for batteries and battery chargers may be shown by submission of existing test reports and does not require additional retesting. 

Compliance to clauses 5 and 6 of EN 15194:2017 +A1:2023 or AS 15194:2016 may be verified by inspection of photographs and does not require further assessment.
 

e-scooters, e-skateboards and hoverboards

• AS/NZS 60335.2.114:2023 - Household and similar electrical appliances- Safety. Part 2.114: Particular requirements for personal e-transporters, or
• EN 17128:2020 - Light motorised vehicles for the transportation of persons and goods and related facilities and not subject to type-approval for on-road use- Personal light electric vehicles (PLEC)- Requirements and test methods, or
• UL 2272:2016 - Electrical systems for personal e-mobility devices (until 1 February 2027) or UL 2272:2014 

e-scooters, e-skateboards and hoverboards batteries

• AS/NZS 60335.2.114:2023 - Household and similar electrical appliances- Safety. Part 2.114: Particular requirements for personal e-transporters, or
• UL 2271:2018 - Batteries for use in light electric vehicle (LEV) applications (until 1 February 2027) or UL 2271:2023.
   

• The product must be manufactured in compliance with the prescribed standard. A sample of each product (model) must be tested by an accredited test laboratory.  
• The test report for each product (model) must be obtained and submitted along with other relevant documentation (specified by certifying body) to either NSW Fair Trading or any other recognised external certification scheme (REAS) for certification, including any other state base electrical safety regulator.  
• The certifying body will verify documentation and issue a certificate of approval for the product with the required product marking.  

• Test reports for certification must be to the full relevant standard including any amendments. 
• Test laboratories can be Australian based or overseas based.  
• Test reports will only be accepted if completed by accredited laboratories. 
• All laboratories must be accredited by the relevant national accreditation body. For example, in Australia NATA (National Association of Testing Authorities, Australia.), or in China CNAS; or in Europe by the relevant accreditation body etc. The certifier will check accreditation. 
   

• Certificates of approval cost approximately $1,200 from NSW Department of Customer Service
• The Gas and Electricity (Consumer Safety) Act 2017 (G&E Act)  will accept recognised external approval schemes (REAS) (the independent certifiers) 
• This is separate from testing which is conducted by accredited test laboratories based in Australia and overseas. Each laboratory sets its own fee structure. 
• Either the manufacturer may apply for the certificate or the Australian importer (supplier). 

NSW Department of Customer Service can typically issue a certificate of approval in approximately one week if all correct information is provided. 

• Once declared all such declared articles must be marked with the relevant approval mark. This includes the certificate number for the product.  
• Marking must be on the product itself and not merely on a packaging.  
• Marking must be 'legible and permanent'. This is typically on the label that shows the model reference code of the device. 
• Examples of marking: 
  NSW mark - NSWxxxxxx 
  REAS mark - ABC-xxxxxx-EA 

See more examples of approval marks.

Access to Standards is provided through licence agreements and third party vendors and are subject to strict copyright and distribution conditions. Please check the Standards Australia website for further information.